Quick reference tools for machinists and field engineers, from 24+ years of on-site work.
All data on this page is for reference only and must be checked against OEM specifications, drawings and tool manufacturers' data before use.
Works out spindle speed and feed rate for turning, boring, facing, milling and drilling. Pick a material to fill in a starting cutting speed, or type your own.
n = (Vc × 1000) ÷ (π × D). Feed rate = f × n (turning) or fz × z × n (milling). When facing, the surface speed falls as the tool moves towards the centre; set the speed for the largest diameter.
Typical starting cutting speeds in m/min for general turning and boring. Portable on-site machines are less rigid than workshop machines and often run with long tool overhang, so start 20–30% lower and adjust for chatter, tool life and finish.
| Material | Examples | HSS (m/min) | Carbide (m/min) |
|---|---|---|---|
| Low-carbon steel | Mild steel, S275, 1018 | 25–40 | 150–250 |
| Medium-carbon steel | EN8 / C45, 1045 | 20–30 | 120–200 |
| Alloy steel (Cr-Mo, Cr-Mo-V) | 42CrMo4, P22 / F22, rotor forgings | 12–25 | 90–160 |
| Cast steel (Cr-Mo, Cr-Mo-V) | Turbine and valve casings | 12–20 | 80–140 |
| Martensitic stainless (12% Cr) | 410, X20Cr13, X22CrMoV12-1 | 10–20 | 80–150 |
| Austenitic stainless | 304, 316 | 10–18 | 80–160 |
| Grey cast iron | EN-GJL-250 | 15–30 | 100–200 |
| Nickel alloys | Inconel 625, 718 | 3–8 | 20–50 |
| Cobalt hard-facing | Stellite valve seats | n/a | 10–30 |
| Copper alloys | Bronze, brass | 30–60 | 150–300 |
| Aluminium alloys | 6082, 7075 | 60–150 | 300–800 |
General guidance only. Always check the insert or tool manufacturer's recommendations for the grade you are using.
Limits and clearance for a hole and shaft fit to ISO 286 (hole-basis and common shaft fits), for nominal sizes up to 500 mm.
Common choices: H7/g6 sliding fit, H7/h6 locating clearance, H7/k6 transition (light press), H7/n6 locating interference, H7/p6 press fit. Values in the size range boundaries follow ISO 286 ("over / up to and including").
Tapping drill ≈ major diameter − pitch (about 75% thread engagement). For Unified threads, pitch = 1 ÷ threads per inch, so a 1″-8 stud gives 1 − 0.125 = 0.875″.
| Thread | Pitch (mm) | Tapping drill (mm) | Thread | Pitch (mm) | Tapping drill (mm) |
|---|---|---|---|---|---|
| M3 | 0.5 | 2.5 | M24 | 3.0 | 21.0 |
| M4 | 0.7 | 3.3 | M27 | 3.0 | 24.0 |
| M5 | 0.8 | 4.2 | M30 | 3.5 | 26.5 |
| M6 | 1.0 | 5.0 | M33 | 3.5 | 29.5 |
| M8 | 1.25 | 6.8 | M36 | 4.0 | 32.0 |
| M10 | 1.5 | 8.5 | M39 | 4.0 | 35.0 |
| M12 | 1.75 | 10.2 | M42 | 4.5 | 37.5 |
| M14 | 2.0 | 12.0 | M45 | 4.5 | 40.5 |
| M16 | 2.0 | 14.0 | M48 | 5.0 | 43.0 |
| M18 | 2.5 | 15.5 | M52 | 5.0 | 47.0 |
| M20 | 2.5 | 17.5 | M56 | 5.5 | 50.5 |
| M22 | 2.5 | 19.5 | M64 | 6.0 | 58.0 |
| Thread | TPI | Tapping drill | Metric drill (mm) |
|---|---|---|---|
| 1/4″ | 20 | #7 | 5.1 |
| 5/16″ | 18 | F | 6.5 |
| 3/8″ | 16 | 5/16″ | 8.0 |
| 7/16″ | 14 | U | 9.4 |
| 1/2″ | 13 | 27/64″ | 10.7 |
| 9/16″ | 12 | 31/64″ | 12.3 |
| 5/8″ | 11 | 17/32″ | 13.5 |
| 3/4″ | 10 | 21/32″ | 16.7 |
| 7/8″ | 9 | 49/64″ | 19.4 |
| 1″ | 8 | 7/8″ | 22.2 |
| 1-1/8″ | 7 | 63/64″ | 25.0 |
| 1-1/4″ | 7 | 1-7/64″ | 28.2 |
| 1-1/2″ | 6 | 1-11/32″ | 34.1 |
Large turbine and casing studs above 1″ are often 8 TPI (8UN series) rather than UNC. Use the calculator above for those.
| Size | TPI | Pitch (mm) | Major dia (mm) | Minor dia (mm) | Tapping drill (mm) |
|---|---|---|---|---|---|
| 1/8″ | 40 | 0.635 | 3.17 | 2.36 | 2.55 |
| 3/16″ | 24 | 1.058 | 4.76 | 3.41 | 3.7 |
| 1/4″ | 20 | 1.270 | 6.35 | 4.72 | 5.1 |
| 5/16″ | 18 | 1.411 | 7.94 | 6.13 | 6.5 |
| 3/8″ | 16 | 1.587 | 9.52 | 7.49 | 7.9 |
| 7/16″ | 14 | 1.814 | 11.11 | 8.79 | 9.3 |
| 1/2″ | 12 | 2.117 | 12.70 | 9.99 | 10.5 |
| 9/16″ | 12 | 2.117 | 14.29 | 11.58 | 12.1 |
| 5/8″ | 11 | 2.309 | 15.88 | 12.92 | 13.5 |
| 3/4″ | 10 | 2.540 | 19.05 | 15.80 | 16.25 |
| 7/8″ | 9 | 2.822 | 22.22 | 18.61 | 19.25 |
| 1″ | 8 | 3.175 | 25.40 | 21.33 | 22.0 |
| 1-1/8″ | 7 | 3.629 | 28.57 | 23.93 | 24.75 |
| 1-1/4″ | 7 | 3.629 | 31.75 | 27.10 | 28.0 |
| 1-1/2″ | 6 | 4.233 | 38.10 | 32.68 | 33.5 |
| Size | TPI | Pitch (mm) | Major dia (mm) | Minor dia (mm) | Tapping drill (mm) |
|---|---|---|---|---|---|
| 1/4″ | 26 | 0.977 | 6.35 | 5.10 | 5.3 |
| 5/16″ | 22 | 1.155 | 7.94 | 6.46 | 6.8 |
| 3/8″ | 20 | 1.270 | 9.52 | 7.90 | 8.3 |
| 7/16″ | 18 | 1.411 | 11.11 | 9.31 | 9.7 |
| 1/2″ | 16 | 1.587 | 12.70 | 10.67 | 11.1 |
| 9/16″ | 16 | 1.587 | 14.29 | 12.25 | 12.7 |
| 5/8″ | 14 | 1.814 | 15.88 | 13.55 | 14.0 |
| 3/4″ | 12 | 2.117 | 19.05 | 16.34 | 16.75 |
| 7/8″ | 11 | 2.309 | 22.22 | 19.27 | 19.75 |
| 1″ | 10 | 2.540 | 25.40 | 22.15 | 22.75 |
| 1-1/8″ | 9 | 2.822 | 28.57 | 24.96 | 25.5 |
| 1-1/4″ | 9 | 2.822 | 31.75 | 28.14 | 28.75 |
| 1-1/2″ | 8 | 3.175 | 38.10 | 34.03 | 34.5 |
Whitworth threads have a 55° thread angle with rounded crests and roots, so they are not interchangeable with 60° UNC/UNF or metric threads, even where the size and TPI match (e.g. 1/4″-20 BSW and UNC).
| Size | TPI | Major dia (mm) | Minor dia (mm) | Tapping drill (mm) |
|---|---|---|---|---|
| G 1/8″ | 28 | 9.728 | 8.566 | 8.8 |
| G 1/4″ | 19 | 13.157 | 11.445 | 11.8 |
| G 3/8″ | 19 | 16.662 | 14.950 | 15.25 |
| G 1/2″ | 14 | 20.955 | 18.631 | 19.0 |
| G 3/4″ | 14 | 26.441 | 24.117 | 24.5 |
| G 1″ | 11 | 33.249 | 30.291 | 30.75 |
| G 1-1/4″ | 11 | 41.910 | 38.952 | 39.5 |
| G 1-1/2″ | 11 | 47.803 | 44.845 | 45.25 |
| G 2″ | 11 | 59.614 | 56.656 | 57.0 |
The pipe size is a nominal bore, not the thread diameter: a 1/2″ BSP thread is about 21 mm across. Tapered pipe threads (BSPT, R / Rp to ISO 7) share the same TPI and sizes but need a smaller drill or a taper reamer; check a taper chart before drilling.
| Size | Major dia (mm) | Pitch (mm) | Tapping drill (mm) |
|---|---|---|---|
| 0 BA | 6.0 | 1.00 | 5.1 |
| 1 BA | 5.3 | 0.90 | 4.5 |
| 2 BA | 4.7 | 0.81 | 4.0 |
| 3 BA | 4.1 | 0.73 | 3.4 |
| 4 BA | 3.6 | 0.66 | 3.0 |
| 5 BA | 3.2 | 0.59 | 2.65 |
| 6 BA | 2.8 | 0.53 | 2.3 |
| 8 BA | 2.2 | 0.43 | 1.8 |
BA threads (47.5°) are found on older UK instrumentation, gauges and electrical fittings.
Roughness grades with Ra in micrometres and microinches, and the processes that typically produce them.
| N grade | Ra (µm) | Ra (µin) | Typical process / use |
|---|---|---|---|
| N12 | 50 | 2000 | Flame cutting, rough sawing |
| N11 | 25 | 1000 | Rough turning and milling |
| N10 | 12.5 | 500 | Roughing passes |
| N9 | 6.3 | 250 | General machining; upper limit of phonographic flange finish |
| N8 | 3.2 | 125 | Standard machined finish; lower limit of phonographic flange finish |
| N7 | 1.6 | 63 | Fine turning and boring; smooth-finish gasket faces |
| N6 | 0.8 | 32 | Fine boring, grinding |
| N5 | 0.4 | 16 | Grinding, honing; precision bores and journals |
| N4 | 0.2 | 8 | Honing, lapping |
| N3 | 0.1 | 4 | Lapping, polishing |
| N2 | 0.05 | 2 | Superfinishing |
| N1 | 0.025 | 1 | Superfinishing |
ASME B16.5 raised-face flanges are normally finished to 3.2–6.3 µm Ra (125–250 µin) with a serrated (phonographic) groove. Ring-joint (RTJ) grooves need a finer finish; follow the flange or gasket specification.